colombo 130 BT Manual cc.cdr

BLAUPUNKT

COLOMBO 130 BT

USB | AUX-IN | BT | TUNER

Enjoy it.

Operating Instructions

Controls – Device

1. BAND/Answer call
2. Power/Mute
3. Push/Menu/Volume
4. Fast Forward/Next
5. Display
6. LCD
7. USB (Music)
8. USB (Charge)
9. Reset function
10. AUX-IN
11. 6/DIR+
12. 5/DIR-
13. 4/RDM
14. 3/RPT
15. 2/SCN
16. 1/
17. Microphone
18. /Rewind/Previous
19. SRC/Call Hand Up

Remote Control Handset

1. Power on / Power off (long press)
2. Band switch: Select FM1/FM2/FM3/MW1/MW2 band in RADIO mode & key in BT mode.
3. Radio tune
4. Track seek
5. EQ
6. Play / Pause
7. Random play
8. Toggle the audio source
9. Volume up / down
10. Mute volume
11. Search function
12. Display switch
13. Repeat play
14. Scan play / Preset scan
15. Auto memory store (long press)
16. Buttons

• [1] Button: Preset station 1.
• [2] Button: Preset station 2.
• [3] Button: Preset station 3.
• [4] Button: Preset station 4.
• [5] Button: Preset station 5.
• [6] Button: Preset station 6.

Installation

Notes:

• Choose a mounting location where the unit will not interfere with the normal driving functions.
• Before finally installing the unit, connect the wiring temporarily and make sure it is all connected properly and the unit and the system work properly.
• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunction.
• Consult with your nearest dealer if installation requires the drilling of holes or other modifications in the vehicle.
• Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
• If installation angle exceeds 30° from horizontal, the unit might not function optimally.

DIN Front/Rear-Mount

This unit can be properly installed either from "Front" (conventional DIN Front-mount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis).

DIN Front-Mount (Method A)

Installation Opening This unit can be installed in any dashboard having an opening as shown below:

Installing the unit

1. Make sure the ignition is turned off, and then disconnect the cable from the -ye terminal of the vehicle's battery.
2. Disconnect the wire harness and the antenna.
3. Lift the top of the outer trim ring then pull it out to remove it.
4. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bend open the appropriate tabs behind the dashboard to secure the sleeve in place.
5. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables.
6. Slide the unit into the sleeve until it locks into place.
7. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (MSmm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicles mounting area. Then use the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. (Not applicable)

Removing the unit

1. Make sure the ignition is turned off, then disconnect the cable from the vehicle battery's negative (-) terminal.
2. Remove the metal strap attached the back of the unit (if attached).
3. Press the release button to remove the front panel.
4. Lift the top of the outer trim ring then pull it out to remove it.
5. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard (Not applicable for all models).

DIN Rear-mount (Method B)

If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm). Note: The outer trim ring, sleeve and the metal strap are not used for Method B installation (Not applicable for all models).

Operations

Turn On/Off the Unit

Turn on the unit by pressing button (2). Press and hold button(2) for 2 seconds to turn off the unit.

MUTE

Short press MUTE button (2) to mute audio output. Press it again to resume output.

SOUND ADJUSTMENT

Short press round button (3) to select the desired adjustment mode. The adjustment mode will change in the following order: BASS-TRE-BAL-FAD-EQ-LOUD

• TRE: Treble
• BAL: Balance
• FAD: Fader
• ED: Equalizer: Short press (3) to select from the preset EQ options as below:
  • FLAT-CLASSICAL-POP-ROCK-EQ OFF

Rotate the volume knob (3) to adjust the desired sound quality or setting.

Reset Function

The RESET button (9) must be activated with either a ballpoint pen or thin metal object when necessary. The RESET button is to be activated only for the following reasons:

• Initial installation of the unit when all wiring is completed.
• Any function buttons do not operate
• Error symbol on the display.

Radio Operation

• Switching To Radio Mode: Press SRC button (2) to select radio mode.
• Selecting a Radio Band: While in Radio mode, press the BAND button (1) to select the desired band from the following options: FM1-FM2-FM3-MW1(AM1)-MW2(AM2).
• Selecting Station: Short Press button (4) or button (18) to activate the Auto seek function.
• Station Storing: Press one of the preset button (1-6) for 2 seconds to store that particular station at that location.

USB Operation

This device is equipped with 2 USB (type A) ports on the front panel (7&8).

USB Ports

• USB port (7) is for media playback.
• USB port (8) is for charging devices only (No media playback is possible from this port).

Supported Mp3/WMA files formats

Bluetooth(BT) Operation

• Pairing: Please access the BT pairing mode in the device you intend to pair with this unit "BP 130".
• Answering/rejecting an incoming call: When there is an incoming call, Press key to answer the call and to reject the call.

Trouble Shooting