TPMS - USB - manual.cdr

BLAUPUNKT

TYRE PRESSURE MONITORING SYSTEM

TPMS IN-DASH USB 4.2
Wireless USB receiver compatible with Android OS radios

Display

• Back
• Setting
• Tyre Position
• Tyre Pressure
• Pressure Unit
• Tyre Temp Temp Unit

APP ON/OFF

APP ON

Insert the USB dongle into the USB port of the radio, then open the app to display TPMS related information on the radio screen.

Note:

1. The APP needs to have been installed in the radio before inserting the dongle in the USB port
2. The tyre data will be shown on the display automatically once the radio is turned ON.
3. The tyre date will be shown on the radio display automatically if there is any abnormal status.

APP OFF

Remove the dongle from the USB port of the radio. Blaupunkt TPMS APP is now disconnected.

Includes

• Receiver X1
• Sensor X4
• Manual X1

Setting Parameters:

1. Click on the TPMS icon
2. Select Function setting
3. Min pressure: Select the low pressure value (Please refer to "Specification" and adjust the value)
4. Temperature: Select the tire temperature unit - °C/°F
5. Max temperature: Select the high temperature value (Please refer to "Specification" adjust the value)
6. Boot time level: Higher the value, this will decide the duration of time the tire information will appear on the main screen of the radio after it's turned ON
7. Car alarm sound: Select the system warning voice-ON / OFF
   Note: If the voice alarm is turned OFF, there will be no audible warning should there be an alarm from the sensors.
8. Device alarm sound: Select the receiver warning - ON / OFF
   Note: If the alarm is turned OFF, there will be no audible warning should there be an alarm from the sensors.
9. Tire programming method: There are three programming methods to program the sensors (Please refer to "Sensor programming" reprogram the sensors)
10. Reset: Restore factory default values - ON / OFF
    Note: When the speed exceeds 25km/h, real-time tire data will be shown on the interface automatically

Different scenarios

Receiver Installation

Insert the receiver into the USB port of the Android Radio USB port.

Sensor Installation

1. Remove the original valve from the vehicle
2. Install sensor in corresponding tyre according to the position sticker on the sensor
3. Inflate the tire
4. Tighten the external nut and valve stem cap
5. Perform a dynamic balance test
6. Adjust & add counterweight by adding required weights

Functional test after installation

1. Display will show real-time tyre data automatically when vehicle speed exceeds 25km/h (15.5MPH)

Installation is complete once all 4 tyre data is received & displayed on the screen at the same time.

Specification

Receiver

• Operating frequency: 433.92±0.05MHZ
• Operating voltage: 5±0.5V
• Operating current: 516mA (at normal status)
  5100mA (at warning status)
• Operating temperature: -20°C +70°C/-4T+158℃
• Pressure range: 0-8Bar/0-116 PSI

Sensor

• Operating frequency: 433.92±0.015MHZ
• Operating voltage: 2.3-3.6V
• Static current: 50.8uA
• Operating temperature: -30 °C +105°C/-22°F +221°F

Adjustable value range

• High pressure value: 2.6-6.OBar/37-86PSI
• Low pressure value: 0.9-3.9Bar/13-55PSI
• High temperature value: 70-90°C/158-194°C

Default value

• High pressure value: 3.3Bar/47PSI
• Low pressure value: 1.7Bar/24PSI
• High temperature: 80°C/176°C

Precision

• Pressure: ±0.1 Bar/±2PSI

Air pressure unit

• 1 Bar = 14.5PSI = 100K Pa = 1.02 K.f/cm

Sensor programming (Reminder: All sensors are pre-programmed)

The system needs to be reprogrammed only when the sensor or receiver is replaced. Click on the icon "⚙️", then select the "Tyre matching", there are three programming methods to commence programming.

1. Sensor match
   A. Select "Sensor match" to enter the programming mode.
   B. Click on the tyre icon you need to reprogram, and then the icon should turn green
   C. Inflate the corresponding tyre until the tyre data is shown on the display
   D. Program the next sensor according as per step B & C, then click on the icon "<" to save and exit programming

Notes

• This system is for vehicles with tyre pressure rating within 6.08bar/86PSI.
• All sensors in this unit have been set individually for each tire at the factory.
• Whenever the location of tyre changes, the sensors must be reprogrammed to the corresponding tyre location.
• The display will turn OFF after the vehicle is turned OFF.
• The battery life of the sensor depends on the use of the vehicle.
• The approval mark and numbers which should be kept permanently, will not affect its installation and functions.
• Do not expose the sensor battery to high temperature or direct flame.
• Do not allow the sensor battery to get wet or store in high humidity conditions. This could cause the battery to malfunction.
• Do not disassemble or tamper with battery in the individual sensors.
• During installation of the sensor tighten the outside nut slowly with 4.0Nm (±0.5) torque in one direction to avoid damaging the sensor.

Disclaimer

• Tyre Pressure Monitoring System (TPMS) is designed for monitoring tire irregularities.
• Driver has responsibility to maintain tyres regularly
• Driver should react promptly once a warning is received from the TPMS kit
• Blaupunkt does no guarantee or assume liability for the loss of sensors

Troubleshooting

1. After installation, there is no tyre data on the display

   • The sensors were not programmed to the display, please reprogram the sensors
   • The display should show the real-time tyre data automatically once the speed exceeds 25km/h

2. There is no tyre data on the display

   • The sensors are not programmed to the display, please reprogram it
   • There is a problem with the sensor

3. The system has a problem if this icon "--" appears occasionally

   • The signal that is transmitted from the sensor is a RF signal and is much like a cell phone signal. The FCC requires to allow all other RF signals to interfere with the system signals and this can cause the monitor to occasionally not display information from the sensors. If this persists then you could have a damaged sensor or the batteries could be weak.

4. Pop up message "USB is connection?" automatically in Blaupunkt TPMS APP.

   • Please make sure that if there are other TPMS APP on the original car system

Warranty

Dear Customer,
Thank you for buying Blaupunkt. To get yourself familiarized with the features and operation of the unit, we suggest you to read the Operating instruction manual provided along with the unit. This Warranty Card is an assurance that you have purchased the best. Please preserve this card to avail Warranty Service during the unlikely event of any problem.

Warranty Terms & Conditions:

• Warranty will be entertained only when this card and the original invoice or sale receipt (as proof of date of purchase, model, serial no. and the dealer’s name) is presented together with the product requiring attention.
• Warranty does not cover damage to Blaupunkt item caused by accident, misuse, unauthorized repairs, additions and modifications carried out by unauthorized dealers or if tampered in any other manner.
• Warranty will not apply if the type or serial number on the product has been altered, deleted, removed or made illegible.
• Warranty does not cover periodic maintenance or replacement of parts due to normal wear & tear.
• This warranty does not cover problem due to improper installation and setup adjustment.
• We reserve the right to refuse warranty service if the above terms and conditions are violated.
• The extent of this warranty is limited only unto the value of the Blaupunkt equipment under warranty.
• In case of any legal or other disputes the same will be under the Courts in Mumbai jurisdiction.